| 319 | 0 | 152 |
| 下载次数 | 被引频次 | 阅读次数 |
为解决传统高强钢材料冲压焊接车架纵梁存在成形工序多、生产周期长、尺寸精度差和装配精度低的问题,提出了一种高强铝合金车架纵梁内高压成形工艺,以7075高强铝合金为材料,通过内高压成形制备车架纵梁,可以有效缩短生产周期,提升产品尺寸精度。基于Dynaform有限元软件对车架纵梁内高压成形进行仿真模拟,研究成形工艺参数对成形质量的影响,分析矩形截面过渡圆角区域的管壁填充行为。对车架纵梁进行试验试制,测量整体尺寸与壁厚分布,对纵梁不同区域的材料进行单向拉伸试验。最终发现在7075铝合金车架纵梁内高压成形过程中,轴向补料量20 mm,成形内压60 MPa,整形内压130 MPa时成形效果最好。对于过渡圆角的填充,管内压强越大、摩擦因数越小,填充效果越好,最终通过实验试制的纵梁长度为2000 mm,宽度为190 mm,高度为70 mm,过渡圆角半径为25 mm,减薄率为18%左右,工件屈服强度480 MPa,抗拉强度560 MPa,整体性能一致性好,尺寸精度更高,生产周期更短,说明7075铝合金通过内高压成形生产的车架纵梁可以满足实际生产的需要。
Abstract：To solve the problems of multiple forming processes, long production cycle, poor dimensional accuracy and low assembly accuracy in traditional high-strength steel material stamping welding of frame longitudinal beams, an internal high-pressure forming process for high-strength aluminum alloy frame longitudinal beam was proposed. Taking 7075 high-strength aluminum alloy as the material, the frame longitudinal beams were prepared through internal high-pressure forming, which can effectively shorten the production cycle and improve product dimensional accuracy. Based on Dynaform finite element software, simulation of high-pressure forming inside the frame longitudinal beam was conducted to study the influence of forming process parameters on forming quality and to analyze the filling behavior of the pipe wall in the transition fillet area of the rectangular section. The frame longitudinal beam was experimentally trialed, the overall size and wall thickness distribution were measured, and the uniaxial tensile tests on materials in different areas of the longitudinal beam were carried out. It is ultimately found that during the internal high-pressure forming process of the high-strength aluminum alloy frame longitudinal beam, the best forming effect is achieved with the axial feeding amount of 20 mm, the forming internal pressure of 60 MPa, and the shaping internal pressure of 130 MPa. For the transition fillet filling, the greater the pressure inside the pipe and the lower the friction factor, the better the filling effect. Finally, the longitudinal beam with the length of 2000 mm, width of 190 mm, height of 70 mm filling, transition radius of 25 mm, thinning rate of about 18%, yield strength of 480 MPa, tensile strength of 560 MPa is produced through experimental trial, and the overall performance consistency is good, the dimensional accuracy is higher, and the production cycle is shorter. It is indicated that the frame longitudinal beam produced by internal high-pressure forming of 7075 aluminum alloy can meet the needs of actual production.
[1]曹晓昂.实施更加符合中国国情的机动车排放标准[J].汽车纵横, 2014,(9):36-39.
[2]朗利辉,杨希英,刘康宁.汽车轻量化成形技术及其进展[J].现代零部件, 2014(4):45-47.
[3] IMANINEJAD M, SUBHASH G, LOUKUS A. Loading path optimization of tube hydroforming process[J]. International Journal of Machine Tools&Manufacture, 2005, 45:1504-1514.
[4] ABRANTES J, LIMA C, BATALHA G. Numerical simulation of an aluminum alloy tube hydroforming[J]. Journal of Materials Processing Technology, 2006, 179:67-73.
[5] KOC M, AUEULAN Y, ALTAN T. On the characteristics of tubular materials for hydroforming-experimentation and analysis[J].International Journal of Machine Tools&Manufacture, 2001, 41:761-772.
[6] NEMATALLA M. Reproducing hoop stress-strain behavior for tubular material using lateral compression test[J]. International Journal of Mechanical Sciences, 2003, 45:605-621.
[7] ASNAFI N, SKOGSGARDH A. Theoretical and experimental analysis of stroke-controlled tube hydroforming[J]. Materials Science and Engineering, 2000, 279:95-110.
[8] AHMETOGLU M, SUTTER K, LI X J, et al. Tube hydroforming:Current research, applications and need for training[J]. Journal of Materials Processing Technology, 2000, 98:224-231.
[9] OLIVEIRA D, WORSWICK M, GRANTAB R, et al. Effect of forming process variables on the crashworthiness of aluminum alloy tubes[J]. International Journal of Impact Engineering, 2006,32:826-846.
[10] KEIGLER M, BAUER H, HARRISON D, et al. Enhancing the formability of aluminium components via temperature controlled hydroforming[J]. Journal of Materials Processing Technology,2005, 167:363-370.
[11] HWANG Y-M, MANABE K-I. Latest hydroforming technology of metallic tubes and sheets[J]. Metals, 2021; 11(9):1360.
[12] MA Y, CHEN S, CHEN D, et al. Determination of the forming limit of impact hydroforming by frictionless full zone hydraulic forming test[J]. International Journal of Material Forming,2021, 14:1221-1232.
[13] MODANLOO V, AKHOUNDI B, KHATIR F A, et al. Investigation of the effect of process parameters in sheet hydroforming process[J]. International Journal on Interactive Design and Manufacturing, 2023, 17(6):3189-3198.
[14] GREY J E, DEVEREAUX A P, PARKER W N. Apparatus for making wrought metal T′s:US28108439A[P]. 1940-06-11.
[15] DAVIS E A. Yield and fracture of medium-carbon steel under combined stress[J]. Journal of Applied Mechanics 1945,(10):13-24.
[16] DOHMANN F, HARTL C H. Hydroforming-A method to manufacture lightweight parts[J]. Journal of Materials Processing Technology, 1996, 60:669-676.
[17] DOHMANN F, HARTL C H. Tube Hydroforming:Research and practical application[J]. Journal of Materials Processing Technology, 1997, 71(2):174-186.
[18] ZHANG J, DAI M, WANG F, et al. Theoretical and experimental study of the free hydroforming of egg-shaped shell[J]. Ships and Offshore Structures, 17(2):257-267.
[19] ZHANG J, DAI M, WANG F, et al. Buckling performance of eggshaped shells fabricated through free hydroforming[J]. International Journal of Pressure Vessels and Piping, 2021, 193:104435.
[20] ZHANG J, CHENG P, WANG F, et al. Hydroforming and buckling of an egg-shaped shell based on a petal-shaped preform[J].Ocean Engineering, 2022, 250:111057.
[21]王仲仁,苑世剑,曾元松,等.无模胀球的原理与研究进展[J].机械工程学报, 1999, 35(4):64-66.WANG Zhongren, YUAN Shijian, ZENG Yuansong, et al. Principle and research progress of dieless ball expansion[J]. Chinese Journal of Mechanical Engineering, 1999, 35(4):64-66.
[22]苑世剑,王小松.内高压成形技术研究与应用新进展[J].塑性工程学报, 2008, 15(2):22-30.YUAN Shijian, WANG Xiaosong. New progress in research and application of Internal high pressure forming technology[J].Journal of Plasticity Engineering, 2008, 15(2):22-30.
[23]王宁华.脉动液压成形条件下管材塑性硬化规律的研究[D].桂林:桂林电子科技大学, 2015.WANG Ninghua. Study on plastic hardening law of pipe under pulsating hydroforming[D]. Guilin:Guilin University of Electronic Science and Technology, 2015.
[24]李欢,李柏週,毛成明,等.基于数值仿真的十字型内高压成形吸能盒优化设计[J].精密成形工程, 2024, 16(1):181-191.LI Huan, LI Bozhou, MAO Chengming, et al. Optimization design of cross shaped internal high-pressure forming energy absorbing box based on numerical simulation[J]. Precision Forming Engineering, 2024, 16(1):181-191.
[25]郭学强,奚建胜.变截面铝合金传动轴管内高压成形工艺参数多目标优化[J].塑性工程学报, 2023, 30(9):27-35.GUO Xueqiang, XI Jiansheng. Multi-objective optimization of internal high pressure forming process parameters for aluminum alloy transmission shaft tube with variable cross section[J]. Journal of Plastic Engineering, 2023, 30(9):27-35.
[26]冯莹莹,孙晓倩,贾越,等. Y形管内高压成形过程数值模拟与实验研究[J].锻压技术, 2023, 48(5):236-244.FENG Yingying, SUN Xiaoqian, JIA Yue, et al. Numerical simulation and experimental research on high-pressure forming process inside Y-shaped pipes[J]. Forging&Stamping Technology,2023, 48(5):236-244.
基本信息:
中图分类号:TG306
引用信息:
[1]孙康,胡志力,龙曲波,等.高强铝合金车架纵梁内高压成形工艺及变形规律[J].塑性工程学报,2025(03):90-98.
基金信息:
湖北省重点研发计划项目(2021BAA200); 湖北省自然科学基金资助项目(2021CFB523); 湖北省科技重大项目(2022AAA001)
2025-04-07
2025-04-07
2025-04-07