| 605 | 8 | 366 |
| 下载次数 | 被引频次 | 阅读次数 |
为了解决传统拼焊制造超薄壁不锈钢波纹管弹性差、寿命短、易破裂等问题，采用液压成形技术成形超薄壁不锈钢波纹管件。针对超薄壁不锈钢波纹管件截面形状复杂以及管壁易失稳起皱破裂的成形难点，设计了不同的加载路径。利用CATIA进行建模，使用Dynaform有限元分析软件进行数值模拟。基于波纹管成形过程中的波高与壁厚减薄情况研究了模具间隙、预胀形内压和整形压力对成形质量的影响规律。试验结果表明，对于复杂异形截面的填充，管内压强和轴向进给的增大有利于材料流动进入圆角区域以及管坯与模具的贴合。对于内径Φ50 mm,壁厚0.4 mm的复杂截面波纹管，预胀形内压7.5 MPa,整形压力20 MPa,轴向进给为20 mm为最佳参数匹配。开展了相关试验，验证了模拟结果与试验结果相符，获得的波纹管满足尺寸与性能的需求。
Abstract：To solve the problems of poor elasticity, short service life and easy rupture of stainless steel bellows with ultra-thin wall made by traditional welding, the hydroforming technology was used to form the stainless steel bellows with ultra-thin wall.Aiming at the forming difficulties that the section shape is complicated and the tube wall is easy to wrinkle and crack of stainless steel bellows with ultra-thin wall, the different loading paths were designed. CATIA was used for modeling and Dynaform finite element analysis software was used for numerical simulation. Based on the wave height and wall thickness thinning during forming process of bellows, the influence laws of die clearance, pre-bulging internal pressure and shaping pressure on the forming quality were studied. The experimental results show that for the filling of complex special-shaped section, the increase of pressure in tube and axial feed is conducive to the material flow into the rounded corner area and the fitting of the tube billet and die. For the special-shaped section bellows with inner diameter of Φ50 mm and wall thickness of 0.4 mm, pre-bulging internal pressure of 7.5 MPa, shaping pressure of 20 MPa and axial feed of 20 mm are the best parameter matching.The related experiments were carried out, it is verified that the simulation results agree with the experimental results, and the obtained bellows meet the requirements of size and performance.
[1] 王彪.5A03铝合金波纹管轴向低压压形工艺[D].哈尔滨：哈尔滨工业大学，2021.WANG Biao.5A03 axial low-pressure shape aluminum alloy bellows technology [D].Harbin:Harbin Industrial University,2021.
[2] 陈庆龙，刘静，吕志勇，等.模具参数对液压胀形双层异质波纹管波形轮廓的影响研究[J].塑性工程学报，2021,28(2):70-78.CHEN Qinglong,LIU Jing,Lü Zhiyong,et al.Study on the influence of die parameters on the corrugated profile of hydraulic expansion double layer heterogeneous bellows[J].Journal of Plasticity Engineering,201,28(2):70-78.
[3] 徐勇，尹阔，靳鹏飞，等.窄波距薄壁波纹管液力成形工艺研究[J].塑性工程学报，2021,28(8):23-29.XU Yong,YIN Kuo,JIN Pengfei,et al.Research on hydraulic forming process of thin wall bellows with narrow wave distance[J].Journal of Plasticity Engineering,2021,28(8):23-29.
[4] 郭煜敬，金光耀，王志刚，等.波纹管液压成形工艺参数对波纹管减薄率的影响[C]//膨胀节技术进展—第十五届全国膨胀节学术会议.合肥，2018:79-85.GUO Yujing,JIN Guangyao,WANG Zhigang,et al.Effect of bellows hydroforming process parameters on bellows thinning rate[C]//The 15th National Expansion Joint Academic Conference.Hefei,2018:79-85.
[5] 孙贺，钱才富，叶梦思，等.波纹管液压成形的数值模拟研究[C]//第十四届全国膨胀节学术会议.合肥，2016:80-86.SUN He,QIAN Caifu,YE Mengsi,et al.Numerical simulation of metallic bellows hydroforming[C]//The 14th Expansion Joint Meeting-Expansion Joint Technology Progress.Hefei,2016:80-86.
[6] 郎利辉，王永铭，段新民，等.复杂薄壁微小截面环形件的充液成形技术研究[J].锻压技术，2011,36(2):34-38.LANG Lihui,WANG Yongming,DUAN Xinmin,et al.Research on liquid filling forming technology of complex thin wall and small section ring [J].Forging & Stamping Technology,2011,36(2):34-38.
[7] 徐勇，张士宏，马彦，等.新型液压成形技术的研究进展[J].精密成形工程，2016,8(5):7-14.XU Yong,ZHANG Shihong,MA Yan,et al.Research progress of new hydraulic forming technology [J].Precision Forming Engineering,2016,8(5):7-14.
[8] 李进楠.超大型U形膨胀节成形模拟及强度与刚度分析[D].北京：北京化工大学，2021.LI Jinnan.Very large U-shaped expansion joint forming simulation and the strength and stiffness analysis[D].Beijing:Beijing University of Chemical Industry,2021.
[9] 孙昌迎.双金属薄壁管冲击液压胀形规律的研究 [D].桂林：桂林电子科技大学，2019.SUN Changying.Research on bulging law of bimetallic thin-walled tube under impact hydraulic pressure[D].Guilin:Guilin University of Electronic Science and Technology,2019.
[10] 高宇.薄壁管件液压成形过程力学特性与工艺研究[D].长沙：中南大学，2012.GAO Yu.Research on mechanical characteristics and technology of thin wall pipe hydroforming process [D].Changsha:Central South University,2012.
[11] 徐丽红.波纹管的成形工艺及模具设计[J].宁波职业技术学院学报，2011,15(5):85-86.XU Lihong.Forming technology and die design of bellows[J].Journal of Ningbo Polytechnic,2011,15(5):85-86.
[12] LEE S W.Study on the forming parameters of the metal bellows [J].Journal of Materials Processing Technology,2002,130:47-53.
[13] OLABI A G,ALASWAD A.Experimental and finite element investigation of formability and failures in bi-layered tube hydroforming[J].Advances in Engineering Software,2011,42(10):815-820.
[14] 叶梦思.基于有限元分析的Ω形波纹管液压成形研究及波纹管轻量化设计 [D].北京：北京化工大学，2018.YE Mengsi.Hydroforming research and lightweight design of ω-shaped bellows based on finite element analysis[D].Beijing:Beijing University of Chemical Technology,2018.
[15] 吕志勇.高温合金矩形波纹管电辅助液压成形规律研究[D].西安：西安石油大学，2021.Lü Zhiyong.High temperature alloy rectangular corrugated tube electric auxiliary hydraulic forming law research [D].Xi′an:Xi′an Shiyou University,2021.
[16] 崔磊.基于响应面法的双层波纹管液压胀形工艺参数优化 [D].西安：西安石油大学，2019.CUI Lei.Optimization of hydraulic bulging process parameters of double-layer bellows based on response surface method[D].Xi′an:Xi′an Shiyou University,2019.
[17] 王刚，张凯锋，吴德忠，等.钛合金波纹管超塑成形工艺研究[J].锻压技术，2003,28(4):28-31.WANG Gang,ZHANG Kaifeng,WU Dezhong,et al.Study on superplastic forming process of titanium alloy bellows[J].Forging & Stamping Technology,2003,28(4):28-31.
[18] 简翰鸣，赵淘，卜星，等.薄壁多层不锈钢波纹管整体成形工艺[J].锻压技术，2021,46(4):81-88,111.JIAN Hanming,ZHAO Tao,BU Xing,et al.Thin layers of stainless steel corrugated pipe forming process [J].Forging & Stamping Technology,2021,46(4):81-88,111.
[19] ALASWAD A,OLABI A G,BENYOUNIS K Y.Integration of finite element analysis and design of experiments to analyse the geometrical factors in bi-layered tube hydroforming[J].Materials & Design,2010,32 (2):838-850.
[20] FARAJI G,BESHARATI M K,MOSAVI M,et al.Experimentaland finite element analysis of parameters in manufacturing of metal bellows[J].The International Journal of Advanced Manufacturing Technology,2008,38(7-8):641-648.
[21] MORI K,MAENO T,MAKI S.Mechanism of improvement of formability in pulsating hydroforming of tubes[J].International Journal of Machine Tools & Manufacture,2007,47(6):978-984.
[22] 李文远.超高强度钢薄壁管件气压热成形技术研究[D].沈阳：东北大学，2018.LI Wenyuan.Ultra high strength steel thin-wall pipe pressure hot forming technology research[D].Shenyang:Northeastern University,2018.
基本信息:
中图分类号:TG394
引用信息:
[1]孙康,洪峰,龙曲波,等.超薄壁不锈钢波纹管件液压成形工艺研究[J],2023,30(11):11-20.
基金信息:
湖北省自然科学基金资助项目(2021CFB523);; 湖北省重点研发计划项目(2021BAA200);; 湖北省科技重大项目(2022AAA001)