| 419 | 9 | 260 |
| 下载次数 | 被引频次 | 阅读次数 |
以6082-T6挤压铝合金防撞梁为例，采用创新低成本挤压铝合金压弯工艺，将薄板冲压的压弯成形及回弹分析方法应用于挤压铝合金的实体压弯工艺。对材料模型、单元类型、网格划分和参数设置等进行了研究，并通过样件试制验证了回弹分析的精度。针对纵向回弹，上、下模型面一致性差以及回弹补偿迭代效率低的问题，提出了弦截法回弹补偿迭代优化流程。将该流程应用于挤压铝合金防撞梁的压弯成形及回弹分析，并获得最终补偿量。最后对压弯模具上、下模型面进行独立补偿。结果表明，该流程能较快较准确地预估挤压铝合金防撞梁上、下模型面的回弹补偿量，指导生产获得合格零件。
Abstract：Taking 6082-T6 extruded aluminum alloy anti-collision beam as an example, the innovative low-cost bending process of extruded aluminum alloy was adopted, and the bending forming and springback analysis methods of sheet stamping were applied to solid bending process of extruded aluminum alloy.The material model, element type, mesh division and parameter setting, etc., were studied.The accuracy of springback analysis was verified through trial production of samples.Aiming at the problems of longitudinal springback, the poor consistency of upper and lower die profiles and low efficiency of springback compensation iteration, the springback compensation iterative optimization process of chord section method was proposed.The process was applied to bending forming and springback analysis of extruded aluminum alloy anti-collision beam, and the final compensation values were obtained. Finally, the profiles of upper and lower bending dies were compensated independently.The results show that this process can predict the springback compensation of upper and lower die profiles of extruded aluminum alloy anti-collision beam quickly and accurately, which guides the production to obtain qualified parts.
[1] 徐文雷，曾宇鹏，李华鑫，等.汽车铝制防撞梁力学性能及虚拟仿真研究[J].汽车工艺与材料，2021,(7):7-11.XU Wenlei,ZENG Yupeng,LI Huaxin,et al.The research on mechanical properties and virtual simulation of aluminum anti-collision beam for automobile[J].Automobile Technology & Material,2021,(7):7-11.
[2] 白梅杉.汽车用铝型材弯曲成形特性研究[D].上海：上海交通大学，2003.BAI Meishan.Research for bending forming behavior of automotive aluminum section-beam[D].Shanghai:Shanghai Jiao Tong University,2003.
[3] 李进军，丁永君，王衬心，等.7A04-T6铝合金圆管的材性试验和本构模型研究[J].钢结构，2019,34(12):35-39.LI Jinjun,DING Yongjun,WANG Chenxin,et al.Research on properties test and constitutive model of 7A04-T6 aluminum alloy tubes[J].Steel Construction,2019,34(12):35-39.
[4] 王誉瑾，范峰，钱宏亮，等.6082-T6高强铝合金材料本构模型试验研究[J].建筑结构学报，2013,34(6):113-120.WANG Yujin,FAN Feng,QIAN Hongliang,et al.Experimental study on constitutive model of high-strength aluminum alloy 6082-T6[J].Journal of Building Structures,2013,34(6):113-120.
[5] 崔广磊，李超，沈盛军，等.铝型材三维拉弯工艺[J].锻压技术，2022,47(2):78-82.CUI Guanglei,LI Chao,SHEN Shengjun,et al.Three-dimensional stretch-bending process for aluminum profile[J].Forging & Stamping Technology,2022,47(2):78-82.
[6] 高嵩，于长春，梁继才，等.铝型材多点三维拉压复合弯曲成形工艺[J].机械工程学报，2019,55(20):152-159.GAO Song,YU Changchun,LIANG Jicai,et al.Multi-points 3D stretch-press bending technology for aluminum profile[J].Journal of Mechanical Engineering,2019,55(20):152-159.
[7] 高嵩，吴宇航，李奇涵，等.铝型材三维拉弯成形回弹预测的理论解析与数值模拟[J].锻压技术，2021,46(4):143-149.GAO Song,WU Yuhang,LI Qihan,et al.Theoretical analysis and numerical simulation on springback prediction for 3D stretch bending of aluminum profile [J].Forging & Stamping Technology,2021,46(4):143-149.
[8] 石永久，程明，王元清.铝合金受弯构件变形性能的非线性分析[J].四川大学学报(工程科学版),2006,38(1):10-14.SHI Yongjiu,CHENG Ming,WANG Yuanqing.Non-linear deformation analysis of aluminum bending members[J].Journal of Sichuan University(Engineering Science Edition),2006,38(1):10-14.
[9] 张深，吴建军，邓良才，等.小直径厚壁管材变曲率弯曲回弹预测[J].材料科学与工艺，2014,22(3):1-6.ZHANG Shen,WU Jianjun,DENG Liangcai,et al.Springback prediction of variable curvature bending for minor diameter thick-walled tube[J].Material Science & Technology,2014,22(3):1-6.
[10] 许亮，徐从昌，李落星.成形温度对铝合金型材挤压-弯曲一体化成形回弹及截面畸变的影响[J].锻压技术，2021,46(9):154-162.XU Liang,XU Congchang,LI Luoxing.Influence of forming temperature on springback and cross-section distortion for aluminum alloy profile during extrusion-bending integration forming [J].Forging & Stamping Technology,2021,46(9):154-162.
[11] 王妍琴，王东，李继光，等.U形7A09铝型材拉弯成形截面畸变控制[J].锻压技术，2022,47(1):119-123,152.WANG Yanqin,WANG Dong,LI Jiguang,et al.Control on section distortion for U-shaped 7A09 aluminum profiles in stretch-bending[J].Forging & Stamping Technology,2022,47(1):119-123,152.
[12] 李晓光，张猛，矫志辉，等.一种基于预压弯的新型扭力梁回弹补偿方法[J].锻压技术，2022,47(6):118-124.LI Xiaoguang,ZHANG Meng,JIAO Zhihui,et al.A springback compensation method on new torsion beam based on pre-compression bending[J].Forging & Stamping Technology,2022,47(6):118-124.
[13] RAMBERG W,OSGOOD W R.Description of stress-strain curves by three parameters [J].National Advisory Committee for Aeronautics,Technical Note,1943,902:1-32.
[14] 张洋.基于挠度控制的轴类零件回弹迭代补偿技术研究[D].秦皇岛：燕山大学，2018.ZHANG Yang.Research on springback iteration compensation technology for shaft part based of deflection control[D].Qinhuangdao:Yanshan University,2018.
基本信息:
中图分类号:TG386
引用信息:
[1]申丹凤,聂昕,陈建.6082-T6挤压铝合金防撞梁压弯成形及回弹补偿[J],2023,30(07):15-22.
基金信息:
湖南省重点研发计划（2022GK2064）;; 柳州市科技计划重大专项（柳科攻2022ABA0104; 2022ABB0101）;柳州市科技计划人才专项（柳科攻2021CBA0101）