| 1,238 | 22 | 111 |
| 下载次数 | 被引频次 | 阅读次数 |
通过热压缩模拟试验和微观组织表征研究了Ti60钛合金在变形温度为975～1080℃、应变速率为0.001～1 s-1下的流变行为和微观组织演化规律。结果表明，Ti60钛合金在高应变速率变形时热效应导致的温升明显，并存在不连续屈服现象。随着变形温度由975℃增加到1080℃,Ti60钛合金变形组织发生混晶组织→双态组织→全针状组织的转变。α单相区变形时，硬取向α晶粒几乎不发生变形和转动，软取向α晶粒在大变形后发生动态再结晶。Ti60钛合金在两相区变形时材料发生α→β相变，当应变速率小于0.1 s-1时，即形成全针状组织，而在应变速率为1.0 s-1时，变形时间短，相变不充分，形成双态组织。此外，α相再结晶机理为不连续动态再结晶，再结晶晶粒尺寸随应变速率的增加而逐渐降低，再结晶晶粒的取向较随机，主要的织构成分为为■(CD压缩方向),最大织构强度约为1.42,且强度随应变速率的升高略有增强。
Abstract：The rheological behavior and microstructure evolution law of Ti60 titanium alloy at the deformation temperature of 975-1080 ℃ and strain rate of 0.001-1 s-1 were studied by hot compression simulation tests and microstructure characterization. The results show that the temperature rise of Ti60 titanium alloy caused by thermal effect is obvious and discontinuous yield phenomenon exists when Ti60 titanium alloy is deformed at high strain rate. With the increase of deformation temperature from 975 ℃ to 1080 ℃, the deformation microstructure of Ti60 titanium alloy undergoes a transition as mixed-grain structure→duplex structure→whole acicular structure. During the deformation in α single-phase region, the hard-oriented α grains hardly deform and rotate, while soft-oriented α grains undergo dynamic recrystallization after large deformation. The α→β phase transition occurs when the titanium alloy is deformed in the two-phase region. When the strain rate is below 0.1 s-1, the whole acicular structure is formed. However, when the strain rate is 1.0 s-1, the deformation time is short and the phase transformation is insufficient, which results in the duplex structure. In addition, the recrystallization mechanism of α phase is discontinuous dynamic recrystallization, and the recrystallization grain size decreases gradually with the increase of strain rate, and the recrystallization grains show random orientation texture with the main texture component ■ (CD indicates the compression direction), the maximum texture strength is about 1.42, and the strength increases slightly with the increase of strain rate.
[1] BOYER R R.An overview on the use of titanium in the aerospace industry [J].Materials Science and Engineering,1996,213(1-2):103-114.
[2] BANERJEE D,WILLIAMS J C.Perspectives on titanium science and technology [J].Acta Materialia,2013,61(3):844-879.
[3] 张志雄，王涛，林鹏，等.钛合金多向锻造工艺研究进展 [J].塑性工程学报，2020,27(8):1-9.ZHANG Zhixiong,WANG Tao,LIN Peng,et al.Recent advances on multi-directional forging of titanium alloy [J].Journal of Plasticity Engineering,2020,27(8):1-9.
[4] 蔡建明，曹春晓.新一代600 ℃高温钛合金材料的合金设计及应用展望 [J].航空材料学报，2014,34(4):27-36.CAI Jianming,CAO Chunxiao.Alloy design and application expectation of a new generation 600 ℃ high temperature titanium alloy [J].Journal of Aeronautical Materials,2014,34(4):27-36.
[5] 徐凯华，刘海军，闫江鹏，等.热等静压态TC4钛合金在多道次热压缩变形中的组织演变[J].塑性工程学报，2021,28(7):150-156.XU Kaihua,LIU Haijun,YAN Jiangpeng,et al.Microstructure evolution of hot isostatic pressed TC4 titanium alloy during multi-pass hot compression deformation[J].Journal of Plasticity Engineering,2021,28(7):150-156.
[6] WEI D X,KOIZUMI Y,NAGASAKO M,et al.Refinement of lamellar structures in Ti-Al alloy [J].Acta Materialia,2017,125:81-97.
[7] HAO F,XIAO J,FENG Y,et al.Tensile deformation behavior of a near-α titanium alloy Ti-6Al-2Zr-1Mo-1V under a wide temperature range [J].Journal of Materials Research and Technology,2020,9(3):2818-2831.
[8] JACKSON M,DASHWOOD R,FLOWER H,et al.The microstructural evolution of near beta alloy Ti-10V-2Fe-3Al during subtransus forging [J].Metallurgical and Materials Transactions A,2005,36(5):1317-1327.
[9] WARCHOMICKA F,POLETTI C,STOCKINGER M.Study of the hot deformation behaviour in Ti-5Al-5Mo-5V-3Cr-1Zr [J].Materials Science and Engineering:A,2011,528(28):8277-8285.
[10] JI X,GUO B,JIANG F,et al.Accelerated flow softening and dynamic transformation of Ti-6Al-4V alloy in two-phase region during hot deformation via coarsening α grain [J].Journal of Materials Science & Technology,2020,36:160-166.
[11] SOUZA P M,HODGSON P D,ROLFE B,et al.Effect of initial microstructure and beta phase evolution on dynamic recrystallization behaviour of Ti6Al4V alloy-An EBSD based investigation [J].Journal of Alloys and Compounds,2019,793:467-479.
[12] CHEN W,ZENG W,XU J,et al.Deformation behavior and microstructure evolution during hot working of Ti60 alloy with lamellar starting microstructure [J].Journal of Alloys and Compounds,2019,792:389-398.
[13] 冯秋元，郭佳林，杨军，等.Ti60高温钛合金的热变形行为I:本构方程[J].塑性工程学报，2021,28(11):158-166.FENG Qiuyuan,GUO Jialin,YANG Jun,et al.Hot deformation behavior of Ti60 high temperature titanium alloy I:Constitutive equations [J].Journal of Plasticity Engineering,2021,28(11):158-166.
[14] 王天祥，鲁世强，王克鲁，等.Ti60合金的流动应力行为及本构关系 [J].塑性工程学报，2019,26(6):271-279.WANG Tianxiang,LU Shiqiang,WANG Kelu,et al.Flow stress behavior and constitutive relationship of Ti60 alloy [J].Journal of Plasticity Engineering,2019,26(6):271-279.
[15] PENG W,ZENG W,WANG Q,et al.Characterization of high-temperature deformation behavior of as-cast Ti60 titanium alloy using processing map [J].Materials Science and Engineering:A,2013,571:116-122.
[16] ZHAO Z L,LI H,FU M W,et al.Effect of the initial microstructure on the deformation behavior of Ti60 titanium alloy at high temperature processing [J].Journal of Alloys and Compounds,2014,617:525-533.
[17] GHOLAMZADEH A,KARIMI TAHERI A.The prediction of hot flow behavior of Al-6%Mg alloy [J].Mechanics Research Co mmunications,2009,36(2):252-259.
[18] 王哲君，强洪夫，王学仁.发生不连续屈服的钛合金高温变形研究进展 [J].中国有色金属学报，2012,22(7):1904-1913.WANG Zhejun,QIANG Hongfu,WANG Xueren.Research and development progress of high temperature deformation of titanium alloy with discontinuous yielding [J].The Chinese Journal of Nonferrous Metals,2012,22(7):1904-1913.
[19] 王立颖，杨友，刘春兰.热机械加工Ti-6Al-4V钛合金的流变行为和显微组织演变 [J].锻压技术，2020,45(12):183-191.WANG Liying,YANG You,LIU Chunlan.Rheological behavior and microstructure evolution on Ti-6Al-4V titanium alloy by hot machining [J].Forging & Stamping Technology,2020,45(12):183-191.
[20] KOIKE J,SHLMOYAMA Y,OHNUMA I.Stress-induced phase transformation during superplastic deformation in two-phase Ti-Al-Fe alloy [J].Acta Materialia,2000,48(9):2059-2069.
[21] LI K,YANG P.Strain-induced α-to-β phase transformation during hot compression in Ti-5Al-5Mo-5V-1Cr-1Fe alloy [J].Transactions of Nonferrous Metals Society of China,2019,29(2):296-304.
[22] ZHAO J,WANG K,HUANG K,et al.Recrystallization behavior during hot tensile deformation of TA15 titanium alloy sheet with substantial prior deformed substructures [J].Materials Characterization,2019,151:429-435.
[23] JIA D,SUN W,XU D,et al.Abnormal dynamic recrystallization behavior of a nickel based superalloy during hot deformation [J].Journal of Alloys and Compounds,2019,787:196-205.
[24] FANG Y,CHEN X,MADIGAN B,et al.Effects of strain rate on the hot deformation behavior and dynamic recrystallization in China low activation martensitic steel [J].Fusion Engineering and Design,2016,103:21-30.
基本信息:
中图分类号:TG146.23
引用信息:
[1]尹宝琴,徐帅,肖纳敏,等.Ti60近α钛合金的热变形行为和组织演化[J].塑性工程学报,2022,29(08):193-202.
基金信息:
国防科工局稳定支持项目(KZ0C191705); 上海市青年科技启明星项目(20QA1405300)
2022-08-23
2022-08-23
2022-08-23